Clone-A-Willy Realistic Vibrator Silicone Penis Moulding Kit, Light Skin Tone

Product Information

This kit is kind of like making pancakes except the batter is going to go bad in 90 seconds and you have to keep a boner the whole time,” James quipped. At least he managed to make a mold of the top half of his penis, allowing him to create a stubby replica of his half-boner, a neon purple “dome” that now sits on his girlfriend’s coffee table. Learn From My Mistakes For those who love things a little frisky and risky, the perfect gift has revealed itself. With the help of this Clone-a-Willy Kit, a perfect silicone copy of either your or your partner's penis can be immortalised. It's a great gift for Valentine's Day or anniversaries or ideal to help spice things up in the bedroom. Be sure to use this product with a water based lubricant. Read the instructions carefully before using this product to avoid any unwanted side effects or reactions. Spice Up Your Sex Life All standard kits include 1 bag of molding powder. This is enough powder to make 1 mold of your penis (as shown in Fig. 2). If you want to be safe, buy a refill! Pour out any water that has accumulated in the bottom of your mould and slowly pour into the silicone. Tape around the edge of the tube. This will be pressed against your body, so you want it to be smooth.

I texted James to see if he’d had success. Nope. He, too, struggled with the molding mixture, and his curved penis kept touching the sides of the tube. (If he’d been less impatient, he would’ve seen that the Clone-A-Willy kit offers a solution for men with curved penises.) Press the tube against your body. The moulding gel will completely solidify in about two more minutes. The same applies to any spilled silicone. I didn't use a disposable bowl when I mixed the bags together and was at first stressed that I had to diligently wash out the still unhardened silicone from my wife's favorite mixing bowl. I later realized it would be smarter to just let the clone harden and peel it all off in one fell swoop and that's exactly what I did In lieu of a Valentine’s Day gift, I wrote my girlfriend a letter explaining what I’d gone through. I finished the letter with, “I tried, I failed, but I will not give up. I need your help, my love.”Now the biggest challenge of the whole process is figuring out how you're going to stay hard for a full minute to ideally two minutes while you insert yourself inside the tube. I highly recommend you figure this out before you begin the process at all. Whether it be by having your spouse do a sexy dance in front of you, having a video queued up, it doesn't matter. Just know that you will have to be erect for a full two minutes with your penis inside of a tube full of molding mixture with only visual/mental stimulus available to keep you erect. I was fortunate enough to have my wife around to tease me, but if she was out doing errands I now think my final product would have been a tad on the chode side of things. Once you've waited the two minutes, let the mold sit for 4-8 hours, waiting the full 8 hours means there will be more detail on the finished cloned willy, so I went with the full eight hours. The bottom line is that you aren't going to feel any stinging or burning and there won't be any long term effects on your penis from using this kit. I went through the steps more or less without a lot of fuss, but there are a couple things I will share with you that might alleviate some of your worries.

Your Clone A Willy Kit comes in an 11 x 2½ inch clear plastic tube, into which you will insert your penis. If your penis is 9” or larger, or you want to make a non-vibrating dildo, keep reading! You'll need some extra materials! If you don't want to use the vibrator, you may need more silicone! Why? When inserted into the tube, the vibrator displaces the silicone. We took this extra volume into consideration when deciding how much silicone to include with our original kits. As far as the finished product is concerned, neither the silicone base nor the catalyst contain any materials that disqualify them from being considered body-safe, so this is a 100% body safe DIY dildo project.Insert the silicone and cardboard assembly into the centre of the filled mould so that the cardboard rests flat against the top of the tube. Ensure to leave enough space for the vibrator to be added, or the mould may overflow. Start your timer. Cut open the bag of white moulding powder, pour it into the bowl of water and start mixing. Stir no longer than 60 seconds.

After letting the impression set, take the two jars of silicone and mix them together as thoroughly as possible in a disposable container. I ended up not using a disposable container and I'll explain what I had to do as a result in the next section. Once the materials have been mixed together, pour out any water that has accumulated in the bottom of the mold and then add the mixture very slowly. You should remember that when you add in the vibrator the silicone will be displaced, so if you are going to use the vibrator don't fill it up all of the way. Now pour the water into a mixing bowl. This step is when the time sensitive parts begin, so make sure to pay attention. You will now cut open the bag of molding powder and stir it into the water for 45 seconds. It won't matter if the mix is a little lumpy still after 45 seconds, time is of the essence here and you just have 45 seconds to get everything mixed as well as you can.Once the mould has gelled, remove your one-eyed trouser snake while leaving the mould inside the tube. To get the most detail, let this sit for four hours before moving on. I asked my friends: “Would a dildo of ‘myself’ make a good gift?” The response was a resounding “yes.” After my inquiry, my best friend, James, liked the idea so much that decided he, too, would craft a dildo for his girlfriend. At least I wouldn't be venturing into uncharted territory alone. Right around this point was when we started to realize we'd overlooked a crucial part of this plan: “ How does one make a dildo of one's penis?” Enter the Clone-A-Willy Kit You then must hasten to shove your erect penis into the mixture "immediately," carefully avoiding touching the sides of tube. The tone of the directions—lighthearted and humorous—outline a process that required careful, diligent planning. As the impetuous man I am, directives such as, “Timing is very important!” stress me out, and I realized how unprepared I was for the Clone A Willy's litany of commands. How It Actually Worked My fantastic confidence in this endeavor and product waned considerably when I unfurled the poster-size directions. The four simple steps had transformed into more than a dozen, and the incredible specificity of each step had me in an immediate state of panic.